All sizes of vials of Ceftazidime Venus Pharma are supplied under reduced pressure.
As the product dissolves, carbon dioxide is released and a positive pressure develops. Small bubbles of carbon dioxide in the constituted solution may be ignored.
Instructions for constitution
See table 7 and table 8 for addition volumes and solution concentrations, which may be useful when fractional doses are required.
Table 7: Powder for Solution for Injection
| Presentation | Amount of diluent to be added (ml) | Approximate concentration (mg/ml) |
| 1 g |
| | Intramuscular Intravenous bolus | 3 ml 10 ml | 260 90 |
| 2 g |
| | Intravenous bolus | 10 ml | 170 |
Note:
• The resulting volume of the solution of ceftazidime in reconstitution medium is increased due to the displacement factor of the drug product resulting in the listed concentrations in mg/ml presented in the above table.
Table 8: Powder for Solution for Infusion
| Presentation | Amount of diluent to be added (ml) | Approximate concentration (mg/ml) |
| 1 g |
| | Intravenous infusion | 50 ml* | 20 |
| 2 g |
| | Intravenous infusion | 50 ml* | 40 |
* Addition should be in two stages.
Note:
• The resulting volume of the solution of ceftazidime in reconstitution medium is increased due to the displacement factor of the drug product resulting in the listed concentrations in mg/ml presented in the above table.
Solution is clear with the defined concentration, diluents and storage conditions used.
Ceftazidime at concentrations between 1 mg/ml and 40 mg/ml is compatible with:
• sodium chloride 9 mg/ml (0.9%) solution for injection
• M/6 sodium lactate injection
• 5% dextrose injection
• 0.9% sodium chloride and 5% dextrose injection
• 10% dextrose injection
Ceftazidime at concentrations detailed in Table 7 may be constituted for intramuscular use with 0.5% or 1% Lidocaine Hydrochloride Injection.
Preparation of solution for bolus injection
1. Insert the syringe needle through the vial closure and inject the recommended volume of diluent. The vacuum may assist entry of the diluent. Remove the syringe needle.
2. Shake to dissolve: carbon dioxide is released and a clear solution will be obtained in about 1 to 2 minutes.
3. Invert the vial. With the syringe plunger fully depressed, insert the needle through the vial closure and withdraw the total volume of solution into the syringe (the pressure in the vial may aid withdrawal). Ensure that the needle remains within the solution and does not enter the head space. The withdrawn solution may contain small bubbles of carbon dioxide; they may be disregarded.
These solutions may be given directly into the vein or introduced into the tubing of a giving set if the patient is receiving parenteral fluids. Ceftazidime is compatible with the intravenous fluids listed above.
Preparation of solutions for iv infusion from ceftazidime injection in standard vial presentation (mini-bag or burette-type set):
Prepare using a total of 50 ml of compatible diluents (listed above), added in TWO stages as below.
1. Introduce the syringe needle through the vial closure and inject 10 ml of diluent.
2. Withdraw the needle and shake the vial to give a clear solution.
3. Do not insert a gas relief needle until the product has dissolved. Insert a gas relief needle through the vial closure to relieve the internal pressure.
4. Transfer the reconstituted solution to final delivery vehicle (e.g. mini-bag or burette-type set) making up a total volume of at least 50 ml, and administer by intravenous infusion over 15 to 30 min.
Note: To preserve product sterility, it is important that the gas relief needle is not inserted through the vial closure before the product has dissolved.
Any residual antibiotic solution should be discarded.
For single use only.
Any unused medicinal product or waste material should be disposed of in accordance with local requirements.