NovoThirteen user instructions
To reconstitute and administer this product the following tools are needed: a 10 ml syringe or a syringe of a convenient size according to injection volume, alcohol swabs, the included vial adapter and an infusion set (tubing, butterfly needle).
Preparing the solution
Always use an aseptic technique. Before starting, the hands should be washed. Bring the powder and solvent vials to a temperature not above 25°C by holding them in the hands. Clean the rubber stoppers on the vials with alcohol swabs and allow them to dry before use.
The product is reconstituted using the vial adapter included.
Attach the vial adapter to the solvent vial (water for injections). Take care not to touch the spike on the vial adapter.
Pull the plunger to draw in a volume of air equal to the total amount of solvent in the solvent vial.
Screw the syringe tightly onto the vial adapter on the solvent vial. Inject air into the vial by pushing the plunger until you feel a clear resistance.
Hold the syringe with the solvent vial upside down. Pull the plunger to draw the solvent into the syringe.
Remove the empty solvent vial by tipping the syringe with the vial adapter.
Click the vial adapter, still attached to the syringe onto the powder vial. Push the plunger slowly to inject the solvent into the powder vial. Make sure not to aim the stream of solvent directly at the powder as this will cause foaming.
Gently swirl the vial until all the powder is dissolved. Do not shake the vial as this will cause foaming. NovoThirteen should be inspected visually for extraneous (for any foreign) particulate matter and discoloration prior to administration. In the event of either being observed, discard the medicinal product.
Reconstituted NovoThirteen is a clear, colourless solution.
If a larger dose is needed, repeat the procedure in a separate syringe until the required dose is reached.
If the patient weighs less than 24 kg, the reconstituted NovoThirteen should be diluted with 6 ml of sodium chloride 0.9%, solution for injection (refer to the section Use in the paediatric population for further detailed instructions on the dilution step).
Important information
Once prepared, NovoThirteen for injection should be used immediately.
Injecting the solution
Ensure that the plunger is pushed all the way in before turning the syringe upside down (it may have been pushed out by the pressure in the vial). Hold the syringe with the vial upside down and pull the plunger to draw up the amount calculated for the injection.
Unscrew the vial adapter with the vial.
The product is now ready for injection.
Safely dispose of the syringe, vial adapter, infusion set and vials. Any unused medicinal product or waste material should be disposed of in accordance with local requirements.
Use in the paediatric population
Dilution of the reconstituted product with sodium chloride 0.9%, solution for injection
If the paediatric patient weighs less than 24 kg, the reconstituted NovoThirteen should be diluted with 6 ml of sodium chloride 0.9%, solution for injection to be able to handle the dosing of small children (see section 4.2 'Posology and method of administration – Paediatric population').
To dilute the reconstituted NovoThirteen the following tools are needed: a vial containing sodium chloride 0.9%, solution for injection, a 10 ml syringe and alcohol swabs.
General instructions for dilution
The dilution should be performed in accordance with aseptic rules.
Carefully draw exactly 6 ml sodium chloride 0.9%, solution for injection, into the 10 ml syringe.
Slowly inject the 6 ml sodium chloride 0.9%, solution for injection, into the reconstituted NovoThirteen vial.
Gently swirl the vial to mix the solution.
The diluted solution is a clear, colourless solution. Check the injection solution for particulate matter and for discolouration. If either is noticed, please discard.
After dilution proceed to the step 'Injecting the solution'.
Any residual material of the diluted product has to be discarded immediately.